Firearm Recalls & Warnings Index
SMITH & WESSON
MODEL 581, 586, 681, 686, or 581-1,
586-1, 681-1, 686-1 & 686CS-1, REVOLVERS
RECALL: Reports have been received from the
field where the combination of a SMITH & WESSON L-FRAME 357 MAGNUM REVOLVER and some .357 Magnum ammunition has
resulted in unacceptable cylinder binding. L-frame revolvers bearing model numbers:
581, 586, 681, 686, or 581-1, 586-1,
681-1, 686-1, 686CS-1
Cylinder binding can cause a failure to fire. Mishandling a revolver while freeing
the cylinder can result in accidental discharge.
Cylinder binding can result from a number of causes, including characteristics of an
individual revolver or the use of ammunition, which does not conform to industry pressure specifications or is particularly fast
burning. Recent developments in ammunition manufacture emphasize the production of .357 Magnum ammunition with increased velocity
and greater primer sensitivity.
Although there have been very few reported incidents of cylinder binding, in view of
our concern for our customer's safety and the reliability of Smith & Wesson products in all circumstances, we issue the
following warning:
In a situation where a failure to fire can be critical - such as law enforcement or
personal protection - do not use .357 Magnum ammunition with an L-frame revolver bearing model numbers 581, 586, 681, 686 or
581-1, 586-1, 681-1, 686-1, 686CS-1 without an "M" over the model number until you have had the revolver modified.
Those who need to use their L-frame revolver under these conditions prior to
modification can safely fire .38 Special caliber ammunition.
Smith & Wesson has developed a modification to improve existing L-frame
revolvers. This improvement enables them to fire all .357 Magnum ammunition, without cylinder binding. Shipments of L-frame
revolvers from our factory after August 21, 1987 already include this improvement.
You can check if your revolver includes this improvement by looking at the left side
of the frame when the cylinder is fully open. If your revolver has been stamped either with a "2" or higher number after
the basic three-digit model number or with an "M" above the model number, your revolver includes this improvement and
does not need modification. If your revolver bears the model number 581, 586, 681, 686, or 581-1, 586-1, 681-1, 686-1, 686CS-1
without an "M" over the model number, it does not include this improvement and your should have your revolver modified.
Smith & Wesson will modify your L-frame revolver free of charge to eliminate the
possibility of cylinder binding with .357 Magnum ammunition. Law enforcement agencies wishing to arrange for modification of
L-frame revolvers should call 800-458-8469 between 9 A.M. and 6 P.M. Eastern time (MA residents call 413-734-8244). Other users
should send their revolvers to a Smith & Wesson Warranty Service Center, specifying "L-frame improvement program"
and enclosing their name and return address.
One of the modifications to improve the L-frame revolver is the installation of a
new hammer nose. This obsoletes all old L-frame hammer noses (part numbers 4702 and 7513) and all old L-frame hammer assemblies
(part numbers 3366, 3378, 3380, 3382, 3391, 4722, 4723, 4726 and 4728) in field parts inventories. Superseded parts should never
be fitted into a modified revolver as this may result in malfunction. It is essential for safety that you return these obsolete
L-frame hammer noses and obsolete L-frame hammer assemblies for a free exchange to:
Smith & Wesson
Service Department
2100 Roosevelt Avenue
Springfield, MA 01101
Do not return L-frame hammer-nose bushings from your spare parts inventory inasmuch
as they are useable in J, N and K-frame revolvers, which are not included in this Product Warning.
We regret any inconvenience this may cause. Smith & Wesson's first concern is
the safety of its products and the protection of its customers.
Source:
-
Shotgun News November 1, 1989; page ?
-
Guns & Ammo, December 1987; page 6
SMITH & WESSON
MODEL 39,
9MM LUGER CALIBER PISTOL
WARNING: An accidental discharge may occur when manually
unloading a pistol if there is an obstruction of the ejection port.
When semiautomatic pistols are manually unloaded:
1. Engage the safety in the "safe" position.
2. Remove the magazine.
3. Point the muzzle in a safe direction.
4. Retract the slide without obstructing the ejection port.
If the primer of a cartridge comes in contact with internal parts, such as the tip of the
ejector, an unintentional discharge may result. This can occur because the cartridge strikes an object which prevents ejection
from the port during the extraction/ejection process.
Source:
- AFTE Journal, July 1980; Volume 12, Number 3:48-50
SMITH & WESSON
MODEL 659,
9MM LUGER CALIBER PISTOL
WARNING: An accidental discharge may occur when manually
unloading a pistol if there is an obstruction of the ejection port.
When semiautomatic pistols are manually unloaded:
1. Engage the safety in the "safe" position.
2. Remove the magazine.
3. Point the muzzle in a safe direction.
4. Retract the slide without obstructing the ejection port.
If the primer of a cartridge comes in contact with internal parts of the pistol, such as the tip
of the ejector, an unintentional discharge may result. This can occur because the cartridge strikes an object, which prevents
ejection from the port during the extraction/ejection process.
Source:
- AFTE Journal, January 1994; Volume 26, Number 1:18-20
SMITH & WESSON
MODEL 439, 459, 469, 539, 559, 639, 659 & 669,
9MM CALIBER, PISTOLS
RECALL: This warning is issued for Smith & Wesson 9mm
Semiautomatic Pistols which were shipped from the factory between May 1, 1983 and February 26, 1986. Included are Models 439,
459, 469, 539, 559, 639, 659 and 669 but only with serial numbers in the following ranges:
A745000-A865000 and TAA0001-TAL9999
The pistols within the serial number ranges listed above must be inspected for function from the
half-cock notch. The safety mechanism will function in a perfectly satisfactory manner in many of these pistols, as well as in all
pistols with serial numbers outside these ranges and in all pistols shipped from the factory after February 26, 1986.
Every one of these models bearing a serial number within the ranges listed above should be
carefully inspected by the owner for this special condition. To determine if your pistol has this condition, do the following:
- Point the muzzle in a safe direction.
- Completely unload the pistol. Check both the magazine and chamber to assure they are empty of
live rounds.
- With your finger off the trigger, operate the manual safety with the unloaded pistol fully
cocked and fully uncocked so that you can recognize how the manual safety looks and feels when it is fully in the safe
position. The hammer will fall from the fully cocked position into the "at rest" position when the manual safety is
moved down toward a safe position. When you are thoroughly familiar with placing the manual safety fully in the safe position,
place it up in the fire position.
- With the manual safety in the fire position, place the hammer in the half-cock notch:
For the Model 439, 459, 539, 559, 639 and 659, put the hammer of your pistol in the
half-cock notch by pulling the hammer to the rear slowly until you hear the first click and then releasing the hammer so that it
catches between the full cock and the "at rest" position.
For the Model 469 and 669, put the hammer of your pistol in the half-cock notch by inserting an empty magazine and slowly
pulling the trigger until you hear the first click and then releasing the trigger so that the hammer catches between the full
cock and the "at rest" position.
- With the hammer in the half-cock notch, push the manual safety down toward the safe position.
If you can push the manual safety fully into the safe position and the hammer falls into the "at rest" position,
your pistol does not require modification. If you cannot push the manual safety fully into the safe position or the
hammer does not fall into the "at rest" position, your pistol is being recalled for modification free
of charge.
Recalled pistols should be sent promptly to a Smith & Wesson Warranty Service Center for
modification. Call 800-633-0164 for the name and location of the one nearest you or for answers to nay questions you may have. Law
enforcement departments who have pistols, which exhibit this condition, should contact the Smith & Wesson Service Department
to arrange for modifying the pistols.
Source:
- AFTE Journal, July 1986; Volume 18, Number 3:68
- AFTE Journal, January 1987; Volume 19, Number 1:36
- American Rifleman, July 1986; page 12
- Shooting Times, August 1986; page 23
- California Department of Justice Firearms Safety Note 86-2
SMITH & WESSON
MODEL 1026, 1076, 4526, 4536, 4576, 5924,
5926, 6924 and 6926 PISTOLS
RECALL: Models affected have frame mounted decocking levers.
Other model Smith & Wesson pistols are not affected by this advisory.
We have determined that it is possible for a Smith & Wesson Third Generation 9mm, 10mm and
.45 ACP pistol with a frame-mounted decocking lever to malfunction so as to make the pistol inoperable.
In order to safeguard our customers from the possibility of such a malfunction, Smith &
Wesson will inspect and, if necessary, modify these pistols free of charge. Owners of Smith & Wesson 9mm, 10mm and .45 ACP
pistols featuring a frame-mounted decocking lever with model numbers listed above, and which do not have two dots stamped on the
frame underneath the decocking lever (when the lever is depressed) should send their pistols and accompanying magazines to Smith
& Wesson for a no-charge inspection.
Please send your pistol and magazines to:
Smith & Wesson
2100 Roosevelt Avenue
Springfield, MA 01102-2208
Attn: Service Department-DL
If you have any questions regarding this product advisory, please call 800-331-0852 ext. 211.
While we have your pistol, our armorers will stamp your pistol with two dots under the decocking
lever, and give your pistol an ultrasonic cleaning and full lubrication (a $25.00 value) at no charge.
We apologize for this inconvenience. Smith & Wesson remains committed to building the safest,
most reliable and finest-performing firearms possible.
Source:
- AFTE Journal, October 1991; Volume 23, Number 4:939
- American Rifleman, October 1991; page ?
- Guns & Ammo, October 1991; page 112
- Shooting Times, November 1991; page 95
- American Handgunner, November/December 1991; page 128
SMITH & WESSON
MODEL 3904, 3906, 3913, 3913LS, 3914, 3914LS,
1006, 1066,
4506, 4516, 4516-1,
5903, 5904, 5906, 5946,
6904, 6906 & 6946, PISTOLS
RECALL: Smith & Wesson has shipped over 300,000 Third
generation Pistols. We have had a very small number or reports where a dropped pistol resulted in a broken grip resulting in a
failure to fire by releasing mainspring tension. Resultant testing and review have shown that a pistol dropped at a specific angle
can cause a fracture of the grip.
As a result of these occurrences and our testing, we have made a change in the grip material to a
thermoplastic alloy of increased durability. This new material, which is now being used on all current production models, can be
identified by a dimple on the bottom of the grip, next to the large opening. Additionally, the blue product box has a green dot
sticker on the label end.
We believe it unlikely that you will experience any problem with your original grips. However, in
order to safeguard our customers from the possibility of such a malfunction, we will make available, free of charge, an easily
installed replacement grip. Please inspect your pistol and if you have a model listed below that does not have a small dimple next
to the large opening, please write us including your model and serial number or call 800-338-2466. If you prefer, you can send
your pistol to a Smith & Wesson Warranty Station where we will replace the grip for you.
Models Affected:
3904, 3906, 3913, 3913LS, 3914, 3914LS, 1006, 1066, 4506, 4516, 4516-1, 5903, 5904, 5906,
5946, 6904, 6906 & 6946
Smith & Wesson's development process is a continuing one. We are constantly striving both to
develop new products and improve existing products. We are committed to building the safest, most reliable, finest performing
firearms possible.
Source:
-
American
Rifleman, August 1990; page 20
-
AFTE Journal,
October 1990; Volume 22, Number 4:452
-
Petersen's Handguns, October
1990; page 25
-
American
Rifleman, October 1991; page ?
-
Guns & Ammo,
September 1990; page 108
SMITH & WESSON
MODEL 4506, 4516, 645 & 745,
45 AUTO CALIBER, PISTOL MAGAZINES
RECALL: It has come to our attention that a small number of
users have experienced cartridge-feeding problems with Smith & Wesson magazines for .45 ACP pistols. This can result in a
failure to feed or jamming, and thereby a failure to fire. The cause of this problem is the magazine.
This recall applies to two types of MAGAZINES ONLY:
Magazines manufactured by Smith & Wesson for Pistol Model number 4516.
Smith & Wesson requests that you inspect your caliber .45 ACP magazine to determine if it is
subject to this recall. To determine if your magazine is affected, follow these simple inspection procedures:
- Inspection Procedure for Magazines for Model 4506, 645, or 745 Pistols.
- Remove the magazine from the firearm following the procedure set forth in the instruction
manual. Before proceeding further, you must ensure that the pistol and magazine are unloaded.
- Examine the butt plate of the magazine. If the butt plate is not molded plastic with a
crescent- shaped cutout molded into the bottom near the front edge, then the magazine is not affected by this recall.
If the butt plate is molded plastic and contains a crescent-shaped cutout molded into the bottom near the front edge,
proceed directly to the next step.
- Carefully inspect each broad flat side of the magazine near the plastic butt plate. If a
punch mark is present above the butt plate on either side of the magazine, your magazine is not affected by this
recall.
- If, however, a punch mark is not present on the right side at the bottom, your magazine must
be replaced.
- Inspection Procedure for Magazines for Model 4516 and 4516-I Pistols.
Any magazines shipped by Smith & Wesson with model 4516-I pistols are already inscribed for
use in that particular model and are NOT subject to this recall.
- Remove the magazine from the firearm following the procedures set forth in the instruction
manual. Before proceeding further, you must ensure that the pistol and magazine are unloaded.
- Inspect each broad flat side of the magazine. If neither side is inscribed "For S&W
M4516 only" or "For S&W M4516-I only"; your magazine must be replaced.
To ensure reliable functioning of your Model 4516 or 4516-I pistol, the model number marked on a
7-round .45 ACP magazine must be identical to all digits of the model number stamped on your pistol. Do not use a Smith &
Wesson magazine marked "M4516 only" in a pistol stamped "MOD 4516".
WARNING: DO NOT USE ONE OF THESE RECALLED MAGAZINES IN YOUR PISTOL FOR A SITUATION WHERE A
FAILURE TO FIRE CAN BE CRITICAL, SUCH AS FOR LAW ENFORCEMENT OR PERSONAL PROTECTION. RETURN AFFECTED MAGAZINES TO SMITH &
WESSON FOR FREE REPLACEMENT.
To receive a free replacement magazine under this recall, send the magazine to be replaced
directly to:
Smith & Wesson
Attention: Magazine Exchange
2100 Roosevelt Avenue
Springfield, MA 01102
Or call toll-free 800-458-8469 between 8 AM and 5 PM EST. You will need to provide the customer
service representative with the model and serial numbers of your pistol. We ask that all affected magazines be returned to Smith
& Wesson in trade for the new magazines.
This toll-free number can also be called if you have any questions concerning this recall.
We regret any inconvenience this may cause; however, this action was dictated by our concern for
the customer's safety and the reliability of Smith & Wesson products in all circumstances.
Source:
-
AFTE Journal,
April 1990, Volume 22, Number 2:227
-
American
Rifleman, January 1990, page ?
-
American
Rifleman, February 1990, page 4
-
Guns & Ammo,
January 1990, page 93
-
Guns & Ammo, February 1990,
page 7
-
Shooting
Industry, January 1990; page 18
-
American Firearms Industry, December 1989; page 13
-
California Department of Justice Firearms Safety Note 89-4
SMITH & WESSON
MODEL SIGMA,
40 S&W CALIBER PISTOL
WARNING: Three
department issue SMITH & WESSON, MODEL SIGMA, 40 CALIBER PISTOLS EXPERIENCED INTERNAL PART FAILURES PREVENTING THE PISTOLS
FROM FIRING.
These pistols had trigger return springs, slide stop springs or sear driver pins break. When
these parts fail the pistol becomes inoperable.
Sgt. Ernie Didier
Glendora Police Department
150 S. Glendora Avenue
Glendora, CA 91741
(626) 914-8250
Source:
- Glendora, CA PD, Teletype Message, December 14, 1998
SMITH & WESSON
MODEL 916-T SHOTG
RECALL: Smith &
Wesson said last week it was recalling all barrels for a 12-gauge, interchangeable barrel shotgun because they are defective and
potentially hazardous.
"Under certain conditions the barrels rupture, but no one has been injured. None of the
barrels exploded," said company spokesman William Clede.
"We learned about the problem from reports in the field," he said.
Owners of the 916T Model, which has been manufactured for several years, should not fire the
takedown type shotgun with its existing barrels, he said. Barrels should be removed from guns and shipped to the factory in
Springfield for replacement.
The company, a major national gun manufacturer, declined to say immediately how many guns were
covered by the recall order.
The company will replace barrels for its 916T Model with new barrels designed not to rupture,
Clede said. The recall does not cover the Model 916 shotgun, which has a fixed barrel.
The newly designed replacement barrels for the 916T will be identified by the letter
"O" on the top of the barrel near the breech end, Clede said.
Contact:
F.J. Longtin
Service Manager
Smith & Wesson
2100 Roosevelt Avenue
Springfield, MA 01101
Source:
- American Rifleman, September 1979; page 74
- American Rifleman, February 1979; page 85
- Crime Control Digest, November 20, 1978; page 6
TANFOGLIO GIUSEPPE/FIREARMS IMPORT AND EXPORT (F.I.E.) CORP.
MODEL TITAN,
.25 CALIBER, SEMIAUTOMATIC PISTOL
WARNING: The Tanfoglio/F.I.E. Corp., Model Titan .25 caliber
semiautomatic pistol has the potential for ACCIDENTAL DISCHARGE.
The owner of one of these pistols was paralyzed when the pistol allegedly fell on its
"uncocked" hammer causing discharge, striking him in the neck.
During a subsequent civil suit against the manufacturer and the importer, the U.S. District Court
awarded the gun owner $10.8 million stating, "Gun manufacturers have an obligation to reasonably anticipate that owners of
guns, will, at some point, unexpectedly drop them. The manufacture of the pistol with a defective firing pin made it virtually
certain that the gun would fire if dropped or bumped on its hammer."
Source:
- Orange County Register, March 1999
- Jackson v. F.I.E. Corp., et al, U.S. District Ct., Eastern District of LA, New Orleans, LA,
# 95-2389 S (12/17/98)
TAURUS,
MODEL 74,
32 SMITH & WESSON CALIBER, REVOLVER
MODEL 80, 82, 84 & 86,
38 SPECIAL CALIBER, REVOLVER
MODEL 94 & 96,
22 LONG RIFLE CALIBER, REVOLVER
WARNING: The listed Taurus revolvers, when dropped from a
height of three feet on the hammer may discharge.
| Revolvers |
Serial Numbers BELOW the
following: |
| Model 74, Blue |
701,219 |
| Model 74, Nickel |
699,118 |
| Model 80, 3" Blue |
1,000,225 (not including 977,537
through 977,582) |
| Model 80, 3" Nickel |
977,656, and 987,259 to 987,358 |
| Model 80, 4" Blue |
1,035,178 |
| Model 80, 4" Nickel |
1,001,684 |
| Model 82, 3" Blue |
996,964 |
| Model 82, 3" Nickel |
1,014,120 |
| Model 82, 4" Blue |
1,025,816 |
| Model 82,4" Nickel |
1,034,375 |
| Model 84, Blue |
1,026,497 |
| Model 84, Nickel |
1,009,613 through 1,009,655
& 1,009,626 through 1,009,655 |
| Model 86 |
1,011,470 |
| Model 94, Blue |
94,170 |
| Model 94, Nickel |
94,206 |
| Model 96 |
97,336 |
Source:
- Shooting Industry, June 1977; page ?
- AFTE Journal, April, 1978; Volume 10, Number 2:33-38
"UNCLE MIKE'S" BRAND GRIPS
for TAURUS, MODEL PT92 & PT99,
9MM CALIBER, PISTOLS
RECALL: Michaels of Oregon is recalling its "Uncle
Mike's" Custom Grade Molded Handgun Grips. Set No. 59507, for Taurus PT92 ad PT 99 semi-automatic 9mm pistols. It has come to
our attention that the trigger bars of some of these pistols can come away from the frame when the pistols are equipped with our
grips. A pistol in this condition could accidentally discharge, causing possible injury or death to the shooter or bystander.
To ensure the safety of our customers and protect them from the possibility of such a
malfunction, we are making available replacement grips. The new grips can be identified by the two cylindrical nubs located on the
inside top of the right grip and the "A" stamped between them. Please inspect your grips and if you do not have the new
grips, mail us your old ones for replacement to the address below. There is no charge for the exchange and we will reimburse you
for postage costs.
"Uncle Mike's" is committed to giving its customers high quality, safe products. We
apologize for this inconvenience to our customers.
Uncle Mike's
P.O. Box 13010
Portland, OR 97213
(503) 255-5890
Source:
- Shooting Times, December 1990; page 77
- Gunweek, November 2, 1990; page ?
THOMPSON CENTER
MODEL RENEGADE, RIFLES
WARNING: These rifles have the potential for an accidental
discharge if the hammer is not in the safety notch position.
Rifles manufactured prior to the mid-1970's may accidentally discharge. When the hammer is pulled
back, prior to reaching the full cock position, a second click is heard. After the second click and prior to reaching full cock,
the hammer can be released and will fall, bypassing the safety notch and firing the rifle.
Source:
- AFTE Journal, April 1983; Volume 15, Number 2:15-16
VEKTOR
MODEL CP1,
9MM CALIBER, SEMI AUTOMATIC PISTOL
WARNING: The Vektor CP1 pistol may accidentally fire when the
loaded firearm is dropped or bumped. DO NOT LOAD OR USE THIS PISTOL. To render this pistol safe remove the magazine from the
firearm, ensure no cartridge is in the chamber, engage the safety and remove the slide from the frame. No authorized solution to
make this pistol safe is currently available. For further information contact:
Vektor, a division of Denel
P.O. Box 5445
Pretoria, 0001
Republic of South Africa
P: 011-27 (12) 620-2616
F: 011-27 (12) 664-1905
Source:
- American Firearms, November/December 2000; Volume 28, Number 11:12
- American Handgunner, January//February 2001; Volume 29, Number 1:114
- American Rifleman, October 2000; page 25
- Shooting Industry, September 2000; page 26
- Company Notice June 24, 2002
Added 7/08/01
Revised 5/25/03
WALTHER
MODEL PP,
32 AUTO CALIBER, PISTOL - FULL AUTO
WARNING: These pistols are subject to unintentional and
uncontrollable full automatic fire if the hammer block (automatic safety) plunger and spring, along with the hammer release
(de-cocking lever) are removed. When the slide is drawn to the rear and released, the acceleration of the slide by the recoil
spring, and the sudden stop as the slide goes into battery causes the hammer to fall. This results in the pistol discharging in a
full automatic mode.
Carl Walther GmbH Sportwaffen
Karlstrasse 33,
D-89073 Ulm, Germany
Source:
- AFTE Journal, January 1996; Volume 28, Number 1:48-54
WALTHER
MODEL P-38,
9MM LUGER CALIBER, PISTOLS
WARNING: Converted to FULLY-AUTOMATIC FIRING
Officers should exercise extreme caution with any Walther P38 type pistol. Law enforcement
agencies at the Federal, State and local levels plus branches of the U.S. and Canadian military service have encountered Walther
P38s having a potentially hazardous conversion.
The conversion consists of a modified firing pin, which is activated by placing the safety in the
safe position. When the safety is placed in this position, the weapon will immediately fire without the trigger being pulled if a
round is in the chamber. If the safety is engaged with the slide open the weapon will fire in the full automatic mode as soon as
the slide is closed. The full automatic is activated by the safety alone. The conversion can be accomplished on post-war P38s made
by Walther or Manurhin, manufactured since April 1940. Full automatic fire may be accomplished by changing the thumb safety lever.
There is no field test, which can be performed to determine if a P38 has this conversion
installed and there are no visible modifications. Consequently, any Walther P38 type pistols encountered should be handled in the
following manner:
- Do not touch the trigger or safety
- Remove the magazine
- Place the safety in the fire position
- Open the slide and ensure that the chamber is empty
Source:
- California Department of Justice Safety Note 86-1
- Bureau of Alcohol, Tobacco & Firearms, National Broadcast September 1985
- Florida Department of Law Enforcement Bulletin, February 1986
- New York State Police Academy Training Bulletin, Number 86-1, May 1986
WEATHERBY INC. Added
5/27/02
MODEL VANGUARD BOLT ACTION, RIFLES
SERIAL # 00001 - 03810; V0001 -
V80966; VX00001 - VX44065; VS0001 - VS23699; VL00001 – VL46984; W0001 – W0099; NV0001 – NV0099
RECALL: If you have a Weatherby, model Vanguard bolt action rifle with a serial number from one of the serial numbers referred to above: USE
OF THIS RIFLE MAY RESULT IN AN ACCIDENT AND SEVERE INJURY. STOP USE OF THIS RIFLE IMMEDIATELY and
visit the Weatherby website at www.weatherby.com
or call Weatherby at 1 (800) 227-2018 to receive a Bolt Return Kit.
Weatherby Inc. of Atascadero, California, is performing a safety
upgrade on all Vanguard by Weatherby brand rifles manufactured between the years 1970 to 1993. The affected rifles bear serial
numbers from one of the following series on the receiver:
-
00001 – 03810
-
NV001 - NV0099
-
V00001 - V80966
-
VL00001 - VL46984
-
VS00001 - VS23699
-
VX00001 - VX44065
-
W001 - W0099
The safety upgrade will prevent
miss-assembly of the bolt, which might occur on the affected rifles. Such miss-assembly might contribute to a hazardous condition
in which the rifle can be accidentally discharged without the bolt being fully engaged, causing severe injury. Only the bolt is
being upgraded. Bolts will be returned to the owners following the upgrade.
Weatherby
3100 El Camino Real
Atascadero, California 93422
(800) 227-2018 Ext. 109
Source:
Added 5/27/02
Revised 5/25/03
WINCHESTER/U.S. Repeating Arms Company
MODEL 70, Bolt
Action Rifles
Calibers:
-
270
Winchester,
-
30-06 Springfield,
-
7mm Remington Magnum,
-
300 Winchester Magnum
RECALL: The
Winchester model 70 bolt action rifles in 270 Winchester, 30-06 Springfield, 7mm Remington Magnum and 300 Winchester Magnum with
serial numbers greater than G2235000 with BLACK COMPOSITE/SYNTHETIC STOCKS may have a
potential safety problem in the front sling swivel stud. There is a possibility that under heavy weight the swivel stud can pull
loose from the composite stock, causing the rifle to fall from the shoulder, which is a dangerous condition.
Sellers and owners of the affected model 70 rifles are being warned to
immediately discontinue any further use until the front swivel stud has been replaced. Many of the affected rifles were sold at
Wal-Mart Discount Stores.
Source:
WINCHESTER
MODEL 490,
.22 CALIBER, SEMIAUTOMATIC RIFLES
RECALL: These rifles are the subject of unintentional
discharge problems. Redesigned parts are available by contacting Winchester.
Winchester Firearms (801) 876-3440
U.S. Repeating Arms Company, Inc.
275 Winchester Avenue,
Morgan, UT 84050
Source:
- AFTE Journal, March 1976; Volume 8, Number 1:28
Corrected 5/25/03
WINCHESTER
MODEL 100, RIFLES AND CARBINES
WARNING: An accidental discharge may occur BEFORE the action
is locked.
These rifles and carbines may have firing pins that can break due to metal fatigue. When lodged
in the breech face they can cause discharge before the action is closed.
Winchester Firearms Notice
Attn: Product Service Department
P.O. Box 10
Cottage Hills, Il 62018
(800) 852-5734
Source:
- AFTE Journal, October 1990; Volume 22, Number 4:452
Corrected 5/25/03
WINCHESTER
MODEL 1001, SHOTGUNS
RECALL: U.S. Repeating Arms Co. has announced an immediate
recall of all Winchester Model 1001 over/under shotguns sold since the introduction in November 1992. No other Winchester
shotguns, past or present, are involved in this recall.
U.S. Repeating Arms Co. officials report that continual and extensive shooting tests have
revealed a safety problem in some guns when subjected to higher than normal pressures. Screening and testing of all Model 1001
shotguns are required. Consequently, U.S. Repeating Arms Co. warns all Model 1001 owners to immediately discontinue any further
shooting of its 1001 shotguns regardless of the type of ammunition used.
To return a shotgun, call U.S. Repeating Arms' Model 1001 Recall Department immediately at
800-945-5372. Arrangements for returning the shotguns will be made at the time. Special shipping boxes preaddressed shipping
labels, and easy instructions will be provided. All shipping costs will be prepaid or quickly reimbursed by U.S. Repeating Arms
Co.
Source:
- Guns & Ammo, January 1995; page 76
- Shooting Times, January 1995; page 8
- Shooting Industry, November 1994; page ?